Data transmission problem??
Moderators: simonB, nick, florent, dylan, Ben
Data transmission problem??
Hello,
I have an issue maybe with my Slesa-U7 interface or ESA software (can't say)
sometimes, either during programming in Editor or User, I have intermittant flashes
like if the interface stops sending data for a cycle. My led fixtures go to off for a short
moment, there is no latching of the last data received in it. It flashes to black then back to normal.
I have latest firmware 1.19, latest ESA app (Dec-10-2012). I have seen it using two different PC's.
I have seen it with 2 or 3 led fixtures hooked up and with a complete setup.
I mostly use ESA, so did not really validate with PRO. Tried ESA2 for a short period and the app.
crashed on me, I stopped using it.
How can I troubleshoot that kind of problem to narrow down the cause?
Serial # 104972
Also is there some documentation about the tabs in the Tools application. Like the DMX timing
tab, test tab etc...?
Thanks, Gaetan
I have an issue maybe with my Slesa-U7 interface or ESA software (can't say)
sometimes, either during programming in Editor or User, I have intermittant flashes
like if the interface stops sending data for a cycle. My led fixtures go to off for a short
moment, there is no latching of the last data received in it. It flashes to black then back to normal.
I have latest firmware 1.19, latest ESA app (Dec-10-2012). I have seen it using two different PC's.
I have seen it with 2 or 3 led fixtures hooked up and with a complete setup.
I mostly use ESA, so did not really validate with PRO. Tried ESA2 for a short period and the app.
crashed on me, I stopped using it.
How can I troubleshoot that kind of problem to narrow down the cause?
Serial # 104972
Also is there some documentation about the tabs in the Tools application. Like the DMX timing
tab, test tab etc...?
Thanks, Gaetan
Re: Data transmission problem??
Hi Gaetan
Try with the test tab in the tools app. Do you have the same problem?
The tools app can be found in the hardware manual here:
http://www.nicolaudie.com/online_manual ... TE-gY7.htm
We need to update it to include information on the DMX timings.
Try with the test tab in the tools app. Do you have the same problem?
The tools app can be found in the hardware manual here:
http://www.nicolaudie.com/online_manual ... TE-gY7.htm
We need to update it to include information on the DMX timings.
Simon
--
Sales/Support
--
Sales/Support
Re: Data transmission problem??
Hello Simon,
Sorry for the delay to answer, I have not used the interface for few months
I have tested with tools, and it still does the same. intermittant flashes. I have tried to change
some timings values, it seemed to be better with fast setting but still has the problem.
Then I tried to disable some items in the configuration, like "port" that I don't use.
After sending the configuration to the interface, it seems dead. Only the the yellow power led
is lit, all other are off and no numbers are on the seven segments display.
When I remove the memory card from the unit, OFF is flashing but as soon as I put it back
nothing is going on.
I need it next wednesday!!, is there a procedure to repair it or to re-initialize to defaults?
Thanks in advance.
Sorry for the delay to answer, I have not used the interface for few months
I have tested with tools, and it still does the same. intermittant flashes. I have tried to change
some timings values, it seemed to be better with fast setting but still has the problem.
Then I tried to disable some items in the configuration, like "port" that I don't use.
After sending the configuration to the interface, it seems dead. Only the the yellow power led
is lit, all other are off and no numbers are on the seven segments display.
When I remove the memory card from the unit, OFF is flashing but as soon as I put it back
nothing is going on.
I need it next wednesday!!, is there a procedure to repair it or to re-initialize to defaults?
Thanks in advance.
Re: Data transmission problem??
Hi, a few things to try:
-replace or format the memory card
-re-write the firmware
-start in bootloader mode (info attached, the same applies to the SIUDI 7)
-replace or format the memory card
-re-write the firmware
-start in bootloader mode (info attached, the same applies to the SIUDI 7)
- Attachments
-
- siudi8_bootloader_mode.pdf
- (227.36 KiB) Downloaded 865 times
Simon
--
Sales/Support
--
Sales/Support
Re: Data transmission problem??
Simon thanks a lot for the procedure. My unit is back alive.
About the flashes, when I use the interface in stand alone, it appears to be fine.
Can it be a problem with the usb input either of the computer or the interface?
Would you suggest changing DMX timing values until there are no more flashes?
Are there "dangerous or minimum" value I should not set the interface to?
Thanks again.
Gaetan
About the flashes, when I use the interface in stand alone, it appears to be fine.
Can it be a problem with the usb input either of the computer or the interface?
Would you suggest changing DMX timing values until there are no more flashes?
Are there "dangerous or minimum" value I should not set the interface to?
Thanks again.
Gaetan
Re: Data transmission problem??
Try changing the DMX timing values and try the latest version of Suite 2 as there have been a few optimisations
Let me know if it's still not working properly
Let me know if it's still not working properly
Simon
--
Sales/Support
--
Sales/Support
Re: Data transmission problem??
Dear friends! I've been using SIUDI7A interface for some time and I see the same problem GaetanP is writing about, glitches in lights behaviour which happen once in a while, sometimes not so often, lets say 2-3 times during a 1-hour show, sometimes much more frequent, like every 10 minutes or so. Same in Sunlite and in Tools / Test tab. And I've never seen any glitches in Standalone mode, haven't tried watching it all day long though)
What I have: SIUDI7A interface, firmware 1.2, drivers 2.1, Sunlite 2 build 1Jul2013 on Windows 7 64bit Ultimate, plugged by a default (and it's new) USB cable into a "back-side" USB port of the Gigabyte ga-z77x-up5 th motherboard
What I have tried besides installing the latest stuff everywhere: different DMX timings, disabling any triggering in Tools / Parameters tab and disabling any MIDI input in Sunlight, using other USB (front panel) ports - nothing seems to change
Right now I'm testing it with the other PC (my wife's Lenovo X100e with Win7 32bit Starter): seems quite smooth if you switch on one scene and don't touch anything BUT is quite likely to produce a glitch or two immediately after the scene is switch on
Any ideas on getting that fixed?
What I have: SIUDI7A interface, firmware 1.2, drivers 2.1, Sunlite 2 build 1Jul2013 on Windows 7 64bit Ultimate, plugged by a default (and it's new) USB cable into a "back-side" USB port of the Gigabyte ga-z77x-up5 th motherboard
What I have tried besides installing the latest stuff everywhere: different DMX timings, disabling any triggering in Tools / Parameters tab and disabling any MIDI input in Sunlight, using other USB (front panel) ports - nothing seems to change
Right now I'm testing it with the other PC (my wife's Lenovo X100e with Win7 32bit Starter): seems quite smooth if you switch on one scene and don't touch anything BUT is quite likely to produce a glitch or two immediately after the scene is switch on
Any ideas on getting that fixed?
Re: Data transmission problem??
Try with tools.exe and put a DMX tester to see if the DMX is dropping out or if it's a problem with your lighting fixture
Simon
--
Sales/Support
--
Sales/Support
Re: Data transmission problem??
I believe if it were a fixture or dmx-chain problem it would definitely show up in standalone mode which still I watch working fine. Anyway, do you think routing SIUDI's dmx output to it's input and watching the numbers in Tools/ Test tab/ Input section will make me see a dropout? I don't have any hardware tester.
Re: Data transmission problem??
If the flash is 1/10th second it only happens 3 times in 4 hours, it would certainly make a good staring contestdo you think routing SIUDI's dmx output to it's input and watching the numbers in Tools/ Test tab/ Input section will make me see a dropout?
Unfortunately a DMX tester would be the only way to get to the bottom of the problem. If you're pretty sure it's an interface problem I can run a tester on it at our office. Send me an e-mail and I can create an RMA
Simon
--
Sales/Support
--
Sales/Support
Re: Data transmission problem??
hi there, i'm back again)
deinstalled Sunlite, deinstalled drivers, installed december version and drivers that are in the package - everything's been very solid since then, thank you very much! 2 days of tests - no glitches!
still wondering if it's your IT-guys who did it or it's just "reinstall-everything-pc-user-style" fix? ;-)
deinstalled Sunlite, deinstalled drivers, installed december version and drivers that are in the package - everything's been very solid since then, thank you very much! 2 days of tests - no glitches!
still wondering if it's your IT-guys who did it or it's just "reinstall-everything-pc-user-style" fix? ;-)